Be Competitive, Be Pro. For Tarantula Pro 8K/Tarantula Pro 8K MenaRD Edition
Windows 10/11 Wired
Android 8.0 or above Wired ( 8K Polling Rate Only Works On PC)
Switch/Switch 2 Wired ( 8K Polling Rate Only Works On PC)
| Status | description |
|---|---|
| Connection | Insert the data cable at the top of the controller into the corresponding device. A steady channel light indicates successful connection |
| Standby | The controller will automatically enter the standby mode after 10 minutes of inactivity while connected |
| Wake-up | Pressing the Home button can wake it up |
| View Mode | Pressing and holding the M button allows you to view the current controller mode |
| Channel Indicator | Mode | Mode Indicator Color | Connection Method |
|---|---|---|---|
| PC | XBOX Mode | Green | Press and hold Home + X Button for 2 seconds |
| Switch | Switch Mode | Red | Press and hold Home + Y Button for 2 seconds |
| Android | Android Mode | Yellow | Press and hold Home + A Button for 2 seconds |
Sticks & Triggers
Set the triggers to long-travel mode. Hold View Button + Menu Button + Home Button for 2 seconds to enter calibration mode. The Home light will flash slowly in white during this process.
Ensure the triggers and sticks are not being touched. Press A Button once.
Rotate both sticks in full circles 2-3 times. Fully press both triggers three times. Finally, press A Button to exit. The Home light will return to its original light effect.
Gyroscope
Place the controller horizontally on a flat surface, then long-pressView Button + Home Button + Down(A)Button for 3 seconds. At this point, the Home indicator willflash red and blue alternately rapidly.
Calibration is complete when the Home indicator returns to its mode color.
Press and hold the Home + Menu buttons for 5 seconds to reset the controller's current configuration to the default settings.
While holding the M button, press the desired remappable button (L4/R4/C1/C2/C3/C4/T1/T2/T3) to enter the recording mode for that button.
The Home light will flash upon entering. Press the button you want to record, and then press the corresponding remappable button again to save and exit.
Up to 32 steps can be recorded at most.
If you exit without pressing the desired button during setup, the button value for that remappable button will be cleared.
While holding the M button, press A/B/X/Y/LB/RB/LT/RT to cycle among Turbo Off
When holding a button with the Turbo function enabled, the Home light will flashred rapidly.
Press and hold M and LT/RT for 2 seconds to turn on and off the hair trigger mode.
Press and hold the M button and press down the Left/Right joystick for 2 seconds to turn onand off the dead zone of the corresponding joystick.
Press and hold the M and A buttons for 2 seconds to shift between the button values of A-B and X-Y
While holding the M button, toggle the left joystick to the Left/Right to cycle the light effect among Solid Color, Breathing, Fantasy(default), Rainbow, Radar, and Off
While holding the M button, move the left joystick up/down to increase/decrease the light brightness
While holding the M button, press the Up/Down button of the D-Pad to increase/decrease color saturation in theSolid Color, Breathing, and Radar modes.
While holding the M button, press the Left/Right button of the D-Pad to decrease/increase the animation speed ofthe Breathing, Fantasy, and Rainbow modes.
While holding the M button, toggle the right joystick upward to switch the controller to the default configuration.
The channel lights are shown as --X--(Indicator light 3 flashes)
While holding the M button, toggle the right joystick upward to switch the controller to the default configuration.
The channel lights are shown as -X-X-(Indicator light 2,4 flashes)
While holding the M button, toggle the right joystick upward to switch the controller to the default configuration.
The channel lights are shown as X-X-X(Indicator light 1,3,5 flashes)
While holding the M button, toggle the right joystick upward to switch the controller to the default configuration.
The channel lights are shown as XX-XX(Indicator light 1,2,4,5 flashes)
The Tarantula 8K PC supports PC via wired connection.
It supports up to 8000Hz polling rate on wired connections.
The controller features Gen-2 TMR sticks. Compared to the first generation, they still use magnetic technology to eliminate physical contact, delivering long-lasting anti-stick drift reliability.
The dual-mode trigger stops allow switching between Hall Effect analog triggers and Micro Switch triggers.
We removed the heavy vibration motors and the battery to reach a weight of just 180g. This pure wired design reduces hand stress, so you can play longer without getting tired.
It has nine remappable macro buttons, including two extra bumpers (T1/T2), two lockable back buttons (R4 / L4) and five front buttons(C1/C2/C3/C4/T3), each supporting up to 32 steps macro recording.
The back button latches allow users to enable or disable the back buttons, helping prevent unintended inputs during gameplay.
Yes. It features a built-in 6-axis gyroscope for motion control.
Yes. It is compatible with GameSir Connect software, allowing users to customize button mapping, macros, and other settings.
The M button is positioned underneath the D-pad.
Configure Generic Controller in Steam
Important tip: When prompted to press the Home/Guide button and Share/Capture button during device input setup, skip these prompts by pressing the A button.
Controllers equipped with a gyroscope are listed below:
Xbox Controllers (Gyro function only available on PC): G7 Pro, G7 Pro Wuchang, G7 Pro Zenless Zone Zero, Tarantula Pro Xbox, T7 Pro Sugar Whirl.
PC Controllers: SuperNova, Cyclone 2, Tarantula Pro, Tarantula Pro 8K, Nova, G7 Pro 8K.
Mobile Controllers: G8+, X5S, X3 Pro, G8+ MFi (Android only)
We do not sell separate spare parts such as controller internal components, replacement buttons, USB ports, standalone receivers, or other internal repair parts. All original bundled accessories included with controllers are not available for individual purchase.
These accessories are manufactured to be used with the controller and are not sold separately.
Currently, the only items sold separately are:
1.Universal data cable,
2.Faceplate for the G7 series, Faceplate for Supernova, Carrying case for the G7 Pro,
3.Detachable Joystick Caps For G7 Pro & Cyclone 2
4.Anti-friction rings,
5.Thumb grip caps,
6.Charger for nova/nova 2 lite, Charger for cyclone 2，Cooler for X5 Lite ,Dongle for nova(Not for nova 1/2 lite)
7.Dongle compatible with the following controllers: Nova (HD), SuperNova, T3S, Tarantula, Cyclone, Cyclone Pro, X5s, G8+.(It Will not work with Cyclone 2, T4, T4 Pro, T4 Pro SE, G7 Pro, Nova Lite, and Nova Lite 2.)
You can view our separately sold accessories here: https://gamesir.com/collections/gamesir-accessories
For Professional Players Competing in Official Tournaments (e.g., CDL, ALGS):
To address tournament regulations regarding prohibited hardware features, we have released the Specific Firmware for Tournament Eligibility for the G7 Pro 8k PC/Tarantula Pro 8K PC.
By installing this firmware, macro and turbo functions will be completely disabled, ensuring the G7 Pro 8k PC/Tarantula Pro 8K PC meets the hardware-legal requirements of major e-sports organizations.
Firmware(G7 Pro 8k PC):https://drive.google.com/file/d/12vk8kZauJTRG9D_Q8IT34pfPZ9Wl8tcX/view?usp=drive_link
Firmware(Tarantula Pro 8K PC):https://drive.google.com/file/d/1g9XWd0T9xFyH5cfsNBSd8ysBSEp0WUaU/view?usp=drive_link
Software(Optional):https://drive.google.com/file/d/1CTsMva4LROYKuw2Bqg1STmwOWr_OxHSN/view?usp=sharing
Note: Please be aware that this firmware will not affect the controller's performance in any way; its sole purpose is to disable specific features to ensure tournament eligibility. If you do not have a requirement for professional competition, please do not install this firmware, as it may negatively impact your personal gaming experience by removing these features.
While on the main page displaying all previously connected controllers, tap the icon in the upper-right corner to change the app language.
To navigate back to this main page after entering a controller configuration page, disconnect your controller or press the AppHome button.
No worries, all GameSir controllers are equipped with overcharging protection, whether used with a charging dock or not. Charging will automatically stop once the controller reaches full battery. Normally, the indicator light turns off upon full charge.
You may calibrate joysticks and triggers either via the software or manually following the steps below:
Notes:
Let us know if you found this helpful or if you need more information.
Get instant answers from skilled players and the GameSir community. Active 24/7.