It supports XBOX Series X|S, XBOX One X|S, Windows 10/11, and Steam.

Wired, with a 3m detachable Type-C cable.

The GameSir™ Hall Effect sticks use non-contact magnetic sensors to prevent stick drift and ensure smooth control, providing an ultra lifespan of up to 5 million cycles.

Yes, it features Hall Effect analog triggers with two-stage trigger stops. You can switch between different trigger travel distances depending on the usage scenario. After switching, please press the trigger fully down three times gently to calibrate. It also includes a Hair Trigger mode, activated by holding M + LT/RT.

It has a total of 4 rumble motors, one in each grip and trigger.

It has 2 mappable back buttons.

Yes, it features a dynamic RGB lighting system, including RGB ABXY buttons, RGB stick rings, and an RGB D-pad.

Yes, it supports customization through the GameSir Nexus app.

1. Confirm whether your USB cable is properly connected to the controller’s USB port.

2. Try plugging the data cable into another USB port on the Xbox or the USB port at the back of the console.

3. Try using a different data cable to see if that fixes the issue.

4. For Kaleid / Kaleid Flux / T7 / T7 Pro W, press View + Menu + M and hold to reset the controller.

Note: If none of the above steps resolve the issue, send your details to gamesir@support.com. Attach a screenshot showing your order number and store name, along with a demonstration video. Also indicate that you’ve already tried the troubleshooting steps outlined on the official website. Our staff will assist you.

Firmly plug in the controller without holding any buttons to ensure a full connection — the controller may produce an audible click when properly seated. Many users have experienced difficulty with this step, with some stating it requires firm force. Several users even returned three units for issues, only to find the fourth unit worked perfectly after being fully plugged in.

Once the controller is plugged in and your PC or Xbox is powered on, hold the controller’s Xbox button to turn it on.

There are a few potential causes. Try all troubleshooting steps below:

PID recognition may fail. While connected, hold Xbox button + M button for 3 seconds, then unplug and replug the controller to switch to the original PID and restore device recognition. If this does not work, hold Xbox button + Share button for 3 seconds while connected to force switching between Xinput and GIP modes.

Try changing USB ports (preferably use ports directly on the motherboard instead of chassis ports or USB hubs) or cables (ensure you use a verified functional data cable). Also confirm the controller runs a stable firmware version.

Known problematic firmware versions for G7 SE/HE: 6.33, 6.38, and 6.5.6, which cause connection-related issues.

To check your firmware version, open GameSir Nexus or Legacy GameSir Nexus.

In GameSir Nexus: Click the upward arrow at the top right labeled "Firmware Upgrade". In Legacy GameSir Nexus: Press the "Updates" button on the controller page to view your current firmware version.

Ensure that you have tried the previously mentioned troubleshooting steps:

Firmly plug in the controller without holding any buttons to ensure a full connection — the controller may produce an audible click when properly seated. Many users have encountered difficulty with this step, with some stating it requires significant force. One user returned three units, only to find the fourth worked after realizing it was never fully plugged in.

Once the controller is plugged in and your PC or Xbox is powered on, hold the controller’s Xbox button to turn it on.

Performing a full shutdown (also known as a power cycle) of the Xbox can often restore controller detection, especially if the controller works normally on a PC.

Plug the controller into the rear USB port of the console. With the console powered on, hold the console’s power button for more than 10 seconds until it fully shuts down and the power indicator turns off. Unplug the console’s power cord from the wall outlet for approximately 30 seconds, then press the console power button 10 times to fully discharge residual power. Keep the controller plugged into the rear port, power the console back on, and check if the controller responds.

The Xbox console enforces a 250 Hz polling rate limit, so the 1000 Hz option is only available on PC.

If GameSir Nexus fails to detect your controller, reset the device in wired mode by holding View + Menu + M buttons simultaneously. This restores the controller’s detection mode.

We do not sell separate spare parts such as controller internal components, replacement buttons, USB ports, standalone receivers, or other internal repair parts. All original bundled accessories included with controllers are not available for individual purchase.

The following items are the only official accessories sold separately:

1. Universal data cables
2. Magnetic faceplates for G7 series; Magnetic faceplates for Super Nova
3. G7 Pro dedicated carrying case
4. Detachable joystick caps for G7 Pro and Cyclone 2
5. Joystick anti-friction rings
6. Universal thumb grip caps
7. Chargers for Nova / Nova 2 Lite; Chargers for Cyclone 2; Cooling fan for X5 Lite
8. Wireless dongle for Nova (not compatible with Nova 1 / Nova 2 Lite)
9. Wireless dongle for Cyclone 2, T4, T4 Pro, T4 Pro SE, G7 Pro, Nova Lite and Nova 2 Lite

You can browse all separately sold official accessories via this link: https://gamesir.com/collections/gamesir-accessories

The M button is positioned underneath the D-pad.

Controllers equipped with a gyroscope are listed below:

1. Xbox Controllers (Gyro function only available on PC): G7 Pro, G7 Pro Wuchang, G7 Pro Zenless Zone Zero, Tarantula Pro Xbox, T7 Pro Sugar Whirl.

2. PC Controllers: SuperNova, Cyclone 2, Tarantula Pro, Tarantula Pro 8K, Nova, G7 Pro 8K.

3. Mobile Controllers: G8+, X5S, X3 Pro, G8+ MFi (Android only)

Try performing the Stick & Trigger Calibration via the app or manually:

1. Hold View + Menu + Xbox buttons, then plug the USB‑C cable into your PC. Release the buttons after plugging in. The indicator will flash slowly in white.

2. Make sure not to touch the triggers or sticks, then press the A button. The indicator will turn off.

3. Fully press LT and RT, and rotate both sticks in full circles three times. Then press the A button. The indicator will turn solid white, indicating calibration is complete.

4. Unplug and reconnect the controller before using it.

Notes:

1. Manual recalibration may succeed when the in‑app calibration fails.
2. Perform calibration at a steady speed with gentle movements to prevent data collection errors.
3. Calibration can be carried out via wired or wireless connection.
4. Calibration only applies to analog trigger mode and does not affect mouse click mode.

Calibration must be performed with the faceplate installed. Calibrating without the faceplate will result in incorrect range values.

Ensure the headset is fully inserted and sits flush with the port; push it in firmly. This is a surprisingly common solution for audio issues.

Additionally, you can adjust the settings here: Settings > General > Volume & audio output > Headset audio > Stereo uncompressed. Some users experience headset problems with other options. If you modified the polling rate, switch it back to 250Hz to prevent extra issues.

If your microphone does not work: Confirm the microphone is not muted. Check the Xbox menu and watch for a red LED near the bottom of the controller. Press the dedicated mute button (on supported controllers) or double-tap M button to toggle mute.

If you are using the controller wirelessly and the microphone works via wired connection but fails wirelessly, update the firmware for both the controller and dongle.

If you encounter microphone echo, disable mic monitoring.

Note: Try reducing headset volume. Loud audio may be picked up by the microphone, particularly with open-back headphones. You may also unplug and reinsert the headset.

Adjust volume and audio mix using these D-pad shortcuts: M button + D-pad Up to raise volume; M button + D-pad Down to lower volume. M button + D-pad Left increases game volume and reduces chat volume; M button + D-pad Right does the reverse.

If audio issues remain after completing these steps, the problem may stem from incompatibility with your headset. Test an alternative headset for troubleshooting. Most headsets compatible with official Xbox controllers (CTIA standard) work with GameSir controllers.

Ensure the controller is fully connected. Firmly plug in the controller without holding any buttons to achieve a complete connection — the controller may produce an audible click when properly seated. Once plugged in and your Xbox is powered on, hold the controller’s Xbox button to turn it on.

Notes: Controllers equipped with cable guards may feel fully inserted even when only halfway connected.

Holding one of the following combinations while plugging in the controller enters DFU mode or manual calibration mode: • Xbox button + Menu button • View button + Xbox button + Menu button

An audio tone will play as an indicator; the tone may vary by model.

If the cable is fully inserted, confirm you are using a functional data-capable cable.

After verifying the above steps, perform a full shutdown (also known as a power cycle) of the Xbox. This often restores controller detection, especially if the controller works normally on a PC.

Plug the controller into the rear USB port of the console. With the console powered on, hold the console’s power button for more than 10 seconds until it fully shuts down and the power indicator turns off. Unplug the console’s power cord from the wall outlet for approximately 30 seconds, then press the console power button 10 times to fully discharge residual power. Keep the controller plugged into the rear port, power the console back on, and check if the controller responds.

You may also refer to additional troubleshooting steps here: https://www.wikihow.com/Clear-Cache-on-Xbox-One. Power cycling clears the Xbox cache and can resolve multiple common issues.

To redeem the code, enter it exactly as printed on the paper at https://www.microsoft.com/redeem or https://www.xbox.com/redeem.

Only non-mobile "Designed for Xbox" controllers work on Xbox consoles. If your controller is built for mobile devices or features the GameSir :881 GameSirButton home button logo instead of the Xbox button, official Xbox console support is not guaranteed.

Currently supported Xbox controllers include: T3 Pro Xbox, T7, T7 Pro, T7 Pro Wireless, G7, G7 SE, G7 HE, G7 Pro Tri-Mode, G7 Pro, Kaleid (K1), Kaleid Flux This list may include unreleased products.

On Xbox consoles, you can adjust the indicator brightness level. Navigate to Settings > General > Accessibility > Night Mode > Controller Brightness and adjust the brightness to your preference.

The bundled promotional Game Pass Ultimate code is only valid for new Game Pass Ultimate members. If you have previously subscribed to Game Pass Ultimate, or if you reside in an unsupported region (see https://www.xbox.com/regions), the code cannot be redeemed on your account.

If your account meets the eligibility criteria but you encounter code-related issues listed below:

• "Invalid code" error even with correct entry
• "Code already redeemed" notification
• Code received after its expiry date
• Illegible code caused by poor printing

Please submit supporting evidence (such as photos or a video showing the Game Pass card and the on-screen error message) via email to support@gamesir.com to apply for a replacement code.

Note: We cannot provide replacement codes for other issues such as temporary server faults.

No worries, all GameSir controllers are equipped with overcharging protection, whether used with a charging dock or not. Charging will automatically stop once the controller reaches full battery. Normally, the indicator light turns off upon full charge.

Feature Summary

1. Stick Curves Stick curves define how the controller converts physical stick movement into input signals. Linear curve means input equals output directly (1 input = 1 output). Other curves deliver different response characteristics. Adjust based on personal preference.

2. Deadzone This parameter controls how much stick movement is required to trigger input registration.

• Initial: The distance you need to move the stick away from the center before input is detected. A higher value requires larger stick movement.
• Max: The distance from the outer edge needed to reach full (100%) input. A lower value achieves maximum input with less travel.

3. Anti-deadzone Designed to compensate for fixed in-game deadzones in games without native deadzone options.

• Initial: Adjusts the starting input value once the stick passes the initial deadzone. A higher value produces a stronger initial signal. Improper configuration may appear similar to stick drift.
• Max: Sets an upper limit for stick output. With a lower value, the stick cannot reach 100% input even when pushed fully to the edge.

4. Hair Trigger

• Static: Any trigger movement within the defined range registers as a full 100% pull. More versatile for general use.
• Adaptive: Trigger registers as 100% once entering the range, yet instantly drops to 0 upon minimal release. Works well for semi-automatic firing, but less ideal for full-auto weapons and aiming down sights.

5. Continuous Trigger

• Off: Standard default trigger behavior.
• On: Acts as a toggle. Press once to hold the input; press again to release.